| General: |
Length (O.A.) |
39 ft 1-1/2
in (11.93 m) |
| Width (O.A.) |
9 ft 0 in (2.74
m) |
| Height (O.A.) |
8 ft 8 in (2.64
m) |
| Weight |
22,000 lbs.
(9979 kg) dry |
| Draft |
22 in (.53 m) |
| Fuel Capacity |
360 gallons
(1363 liters) |
| Flotation: |
Pontoons--Two 36 in x 32 in x 33 ft (.91 m x .81 m x 10
mm)10 Gauge (3.4 mm)Steel with Internal Bulkheads and Stiffeners;
formed for rigidity; polyurethane foam filled. |
Cutter
Assembly: |
Auger Diameter |
13-5/8 in (346
mm) |
| Auger Pitch |
11 in (279 mm) |
| Auger Flighting |
3/8 in (9.5
mm) |
| Speed |
Variable to
106 RPM |
| Cutter Knives |
Detachable Heat-Treated
Blades |
| Auger Torque |
16,500 in-lbs.
(189.8 kg-m) |
| Rotates to Cut Slope up to 45 degrees |
| Mud Shield: |
19
in x 9 ft (.48 m x 2.74 m) Hydraulically Adjustable |
Working
Capacity: |
Cut
9 ft (2.74 m) wide x 18 in (.46 m) maximum depth |
| Operating Depth |
15 ft (4.57
m) Maximum |
| Engine: |
Detroit Diesel 6-71N; 228 BHP (170 kw continuous power)
at 2100 RPM |
| Drive: |
Clutch-Manual, 14 in (356 mm) Dia. Disc & Pressure Plate |
| Single Gear Reduction Ratio 1.8:1 |
| Drive Coupling-Flexible Element Type |
| Pump: |
Centrifugal Recessed Impeller, 3 Vane |
| Impeller Diameter |
19-1/2 in (495
mm) |
| Suction Diameter |
8 in (203 mm) |
| Discharge Diameter |
8 in (203 mm) |
| Shaft Diameter |
2-7/8 in (73
mm) |
| Nominal Pump Performance |
2000 GPM (7570
liters/min) at 1160 RPM against 176 ft (53.65 m) Head |
Service
Water Pump: |
Capacity |
75 GPM (284
liters/min) at 800 RPM |
| Pressure |
184 ft (56 m)
Total Dynamic Head |
Hydraulic
System: |
Dual Pumps |
| Capacity Total |
30.0 GPM (113.6
liters/min) at 2100 RPM |
| Reservoir |
47 Gallons (178
liters) at full mark |
| Circuit One |
Auger Drive |
| Circuit Two |
Boom, Mud Shield
and Winch |
| Relief Valve
Setting, Auger |
3000 PSI (211
kg/cm2) |
| Relief Valve
Setting, Others |
1800 PSI (127
kg/cm2) |
| Propulsion: |
Treble Sheave Hydraulic Winch (13 in (330 mm) Drum Winch
optional) |
| Traverse Speed |
34 FPM (10.36
m/min) Maximum Forward & Reverse |
| Average Cutting
Speed |
8 to 12 FPM
(2.44 to 3.66 m/min) |
Electrical
System: |
Voltage |
12V |
| Alternator Output |
65 Ampere |
| Batteries |
(2) 12V, 205
Ampere Hour, Parallel Wired |
| Circuits |
2 Wire System
Full Ground |
| Finish: |
Polyurethane finish coat on corrosion inhibitive epoxy primer. |
| Colors: |
Standard Colors |
Red, White and
Blue |
| NOTE: |
Specifications Subject To Change Without Notice.
Optional configuration quoted upon request. |
